Alimentazione ad alta tensione ad alta tensione.
Ottieni l'ultimo prezzoTipo di pagamento: | T/T |
Incoterm: | FOB,CFR,CIF,EXW |
Quantità di ordine minimo: | 1 Piece/Pieces |
Trasporti: | Ocean,Land,Air,Express |
Porta: | SHANGHAI,NANJING,QINGDAO |
Tipo di pagamento: | T/T |
Incoterm: | FOB,CFR,CIF,EXW |
Quantità di ordine minimo: | 1 Piece/Pieces |
Trasporti: | Ocean,Land,Air,Express |
Porta: | SHANGHAI,NANJING,QINGDAO |
Modello: CCP - 6U
marchio: Idealteknic
Luogo D'origine: Cina
Potenza Di Uscita: > 500 W.
Input Voltage: Three Phase 380vac
Input Frequency: 50/60hz
Working Principle: Pwm
Power Supply Type: Igbt-Based
Working Mode: Constant Voltage / Constant Current
Display Mode: Digital Led
Control Mode: 10-Turn Potentiometers
Protections: Ocp, Short Circuit And Load Discharging Protections Etc., Ocp, Short Circuit And Load Dischargin
Applications: Lab Test / Hipot / Capacitor Charging
Circuit Mode: Pwm
Output Voltage Range: 1 Kv ~ 100 Kv
Output Current Range: 60 Ma ~ 6000 Ma
Tipo Di Output: Single
Cooling: Forced Air Cooling
Unità vendibili | : | Piece/Pieces |
Tipo pacchetto | : | Caso in compensato |
Esempio immagine | : | |
Scaricare | : |
Serie CCP ad alta tensione ad alta tensione DC Alimentatore DC
Panoramica
Gli alimentatori ad alta tensione della serie CCP-6U si espandono e aggiorna la capacità di uscita sulla base dei alimentatori di ricarica di condensatori ad alta tensione CCP-4U. Adotta un telaio da 19 pollici da 19 pollici a monte rack 6U, la potenza di uscita può raggiungere 6kW e il livello di tensione di uscita è 1KV / 2KV / 3KV / 4KV / 5KV / 6KV / 8KV / 10KV / 12KV / 15KV / 20KV / 30KV / 30KV / 40KV / 50KV / 60KV / 70KV / 80KV / 100KV, questa serie di alimentatori di ricarica di condensatori ad alta tensione espande la tensione di uscita e la gamma di alimentazione sulla base di manutenzione di elevata efficienza, alta velocità di risposta di uscita e caratteristiche di auto-recupero di protezione più veloci.
La tensione di uscita e la corrente degli alimentatori di ricarica del condensatore HV possono essere controllati e letti attraverso il pannello di controllo anteriore. Inoltre, questa serie di alimentatori ad alta tensione ad alta tensione di condensatore sono inoltre dotati di un'interfaccia DB50 di serie. I clienti possono modificare il software di controllo in base al nostro protocollo di comunicazione o applicare segnale di contatto 0 - 10 V sull'interfaccia in base alla nostra definizione dell'interfaccia per ottenere il controllo e il monitoraggio degli HVP di ricarica del condensatore, come avviamento/arresto ad alta tensione, impostazioni di uscita e letture.
Con le funzioni di protezione complete, il caricabatterie del condensatore HV può gestire la sovratensione, la sovracorrente, la scarica di carico e altre situazioni.
Caratteristiche
l Può essere utilizzato come alimentatore HV DC o come alimentatore di ricarica di condensatori HV.
l Tensione di uscita regolabile dallo 0 al 100%
l Potenza di uscita: ricarica media @ 3KJ/s e la potenza di ricarica di picco può raggiungere 3KW.
l Carica in modalità corrente costante e passa alla modalità di corrente costante fino a quando non è completamente carica.
l Sistema a doppio isolato unico, forte capacità anti-interferenza.
l Raffreddamento ad aria forzata, design molto robusto.
Applicazioni
l Impianto del raggio ionico.
l Processo a semiconduttore.
l Saldatura del fascio di elettroni.
l Carica del condensatore.
l Trasmettitore RF ad alta potenza.
l Precipitatore elettrostatico.
l Sistema a raggi X.
1. Questo modulo di alimentazione ha un'output HV, solo una persona professionale potrebbe gestirlo.
2. Assicurati di una buona messa a terra prima dell'operazione.
3. L'alimentazione di ricarica del condensatore ha un'energia internamente immagazzinata, non si prega di funzionare senza caricamento.
4. Mantieni pulito il modulo di potenza e una buona ventilazione.
5. Connettori di ingresso e output HV o carico HV senza tocco.
Nota: tutti i modelli hanno una complicazione di base tra cui linea di input, linea HV, linea GND, linee di interfaccia ... ecc.
Input |
Voltage |
Three-phase 380Vac (input tolerance: 10%) |
|
Frequency |
50Hz/60Hz |
||
Connection |
Input line provided by iDealTek. (1.5 meters) |
||
Output |
Rated power |
3KW ~ 6KW (Max.) available ** |
|
Output voltage adjusting range |
1KV / 2KV / 3KV / 4KV / 5KV / 6KV / 8KV / 10KV / 12KV / 15KV / 20KV / 30KV / 40KV / 50KV / 60KV / 70KV / 80KV / 100KV available ** (For other output voltages, please contact us for details) |
||
Output current adjusting range |
0A ~ ****mA |
||
Output polarity |
Positive or Negative (both available) Client must choose one output polarity before ordering. |
||
Line regulation |
≤0.1% for ±10% change in input voltage. |
||
Load regulation |
≤0.1% for no load to full load at output. |
||
Ripple (Vr.m.s.) |
≤0.1% @ rated output. |
||
Output connection |
Detachable shielded high-voltage cable provided by IdealTek. (3 meters) |
||
Efficiency |
≥90% |
||
Setting & Display |
Output control mode |
Local |
10-turn potentiometer on front panel. |
Remote |
DB50 analog port & RS485 communication port. |
||
Display mode |
Display mode |
41/2 LED digital display |
|
Display resolution |
≤1% (range: 5%~100% of the rated value) |
||
Protection & Monitoring functions |
Load discharging protection |
When the load has discharging due to insufficient safety distance between load and ground, the power supply shutdown the high voltage output, and then restarts, so cycle like this till the discharging fault is eliminated. |
|
Short circuit protection |
When a short circuit occurs between the load and the ground, the power supply works in constant current mode, the current is limited to the maximum value, and the voltage drops to 0 to protect the internal inverter from damage. |
||
Over current protection |
When the users' load exceeds the rated load and cause over-loading, the power supply works in constant current mode, the power supply output current does not change, and output voltage decreases. |
||
Noise |
≤65dB |
||
Protection degree |
IP20 |
||
Cooling method |
Forced air cooling (Front inlet, rear outlet) |
||
Working environment conditions |
Ambient temperature |
0℃~40℃ |
|
Humidity |
10%~90% (non-condensing) |
||
Height |
≤2000m |
||
Storage environment conditions |
Ambient temperature |
-20℃~60℃ |
|
Humidity |
10%~90%(non-condensing) |
||
Height |
≤2000m |
||
Size (W*H*D) (mm) |
483*266*573 (19” sub-rack 6U chassis) |
||
Weight |
45KG (1KV ~ 10KV) 55KG (20KV ~ 100KV) |
||
|
Front panel description |
||
|
||
No. |
Description |
|
1 |
Power Switch (POWER) |
|
2 |
HV ON / OFF Switch (HV) |
|
3 |
Local / Remote Switch (LOCAL / REMOTE) |
|
4 |
Analog / RS communication Switch |
|
5 |
HV adjusting knob |
|
6 |
Current adjusting knob |
|
7 |
HV output display |
|
8 |
Output current display |
|
9 |
Emergency Button |
|
10 |
Reset switch |
|
Front Panel Indicator Lights Description |
||
|
||
Indicator lights name |
Description |
|
POWER ON |
After the CONTROL POWER switch is set to the ON position, the light becomes on, indicating that the power input has been connected and the power supply is normal. |
|
HV ON |
After the HV switch is set to the ON position, the light becomes on, indicating that the high-voltage output of the power supply is started and the power supply is normal. |
|
CONST HV
|
When the light is on, it indicates that the power supply is working in a constant voltage state. |
|
CONST mA |
When the light is on, it indicates that the power supply is working in a constant current state. |
|
CONST POW |
When the light is on, it indicates that the power supply is working in a constant power state. |
|
OVER VOLTAGE |
When the light is on, it indicates that the power supply has a high voltage overvoltage fault. |
|
INV OVERI |
This light is on, indicating that the power supply has an inverter overcurrent fault. |
|
INV OVER TEMP |
This light is on, indicating that the power supply has an inverter over-temperature fault. |
|
HV OVER TEMP |
When the light is on, it indicates that the power supply has an over-temperature fault with the high-voltage part. |
|
SPARK EXCEEDED |
When the light is on, it indicates that the power supply has a discharge fault. |
|
AC FAULT |
When the light is on, it indicates that there is an AC fault (overvoltage or under voltage) fault in the power supply. |
|
EMERGENCY |
When the light is on, it indicates that the power supply is in an emergency stop state with faults. |
|
INTERLOCK |
When the light is on, it indicates that the power supply is in an interlocked state and the power supply is normal. |
|
Rear panel description |
||
|
||
Mark |
Description |
|
E1 |
Grounding bolt |
|
J1 |
HV output interface |
|
JB1 |
DB50 control interface |
|
CB1 |
Main power switch |
|
LINE INPUT |
Power Supply input interface Three – phase, four – wire (L1 è Black, L2 è Red, L3 è Grey, Null è Blue, PE è Green) |
|
AIR EXHAUST |
Cooling fans |
KV |
mA |
P (KW) |
Model |
KV |
mA |
P (KW) |
Model |
1 |
6000 |
6 |
CCP-(N/P)6kW-1kV |
15 |
400 |
6 |
CCP-(N/P)6kW-15kV |
2 |
3000 |
6 |
CCP-(N/P)6kW-2kV |
20 |
300 |
6 |
CCP-(N/P)6kW-20kV |
3 |
2000 |
6 |
CCP-(N/P)6kW-3kV |
30 |
200 |
6 |
CCP-(N/P)6kW-30kV |
4 |
1500 |
6 |
CCP-(N/P)6kW-4kV |
40 |
150 |
6 |
CCP-(N/P)6kW-40kV |
5 |
1200 |
6 |
CCP-(N/P)6kW-5kV |
50 |
120 |
6 |
CCP-(N/P)6kW-50kV |
6 |
1000 |
6 |
CCP-(N/P)6kW-6kV |
60 |
100 |
6 |
CCP-(N/P)6kW-60kV |
8 |
750 |
6 |
CCP-(N/P)6kW-8kV |
70 |
86 |
6 |
CCP-(N/P)6kW-70kV |
10 |
600 |
6 |
CCP-(N/P)6kW-10kV |
80 |
75 |
6 |
CCP-(N/P)6kW-80kV |
12 |
500 |
6 |
CCP-(N/P)6kW-12kV |
100 |
60 |
6 |
CCP-(N/P)6kW-100kV |
|
l 0 ~ 10V Controllo del segnale analogico (interfaccia DB50)
l RS Communication Interface (RS485 Communication Port)Disegni (solo per riferimento) |
6U Chassis ( (2KW ) (RAL7035) |
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.